Re: [squid-users] Cisco with WCCP!! newbie here..

hello :)
I've took a break of working live on squid and started reading more about it
to see what I'm getting myself into..
I managed to get the router and squid to see each other and troubleshoot the
GRE tunnel..
sh ip wccp shows hits.. but when I check the access.log and cache.log of
squid I see nothing..
any idea what might be causing this?
heres the output of router debug:

6 17:10:14.012: WCCP-PKT:D90: Received valid Here_I_Am packet from
192.168.0.2 w/rcv_id 00000020
6 17:10:14.012: WCCP-PKT:D90: Sending I_See_You packet to 192.168.0.2 w/
rcv_id 00000021
6 17:10:14.016: WCCP-PKT:D80: Received valid Here_I_Am packet from
192.168.0.2 w/rcv_id 00000020
6 17:10:14.016: WCCP-PKT:D80: Sending I_See_You packet to 192.168.0.2 w/
rcv_id 00000021
6 17:10:31.504: WCCP-PKT:D90: Received valid Here_I_Am packet from
192.168.0.2 w/rcv_id 00000021
6 17:10:31.504: WCCP-PKT:D90: Sending I_See_You packet to 192.168.0.2 w/
rcv_id 00000022
6 17:10:31.508: WCCP-PKT:D80: Received valid Here_I_Am packet from
192.168.0.2 w/rcv_id 00000021
6 17:10:31.508: WCCP-PKT:D80: Sending I_See_You packet to 192.168.0.2 w/
rcv_id 00000022
6 17:10:48.640: WCCP-PKT:D90: Received valid Here_I_Am packet from
192.168.0.2 w/rcv_id 00000022
6 17:10:48.640: WCCP-PKT:D90: Sending I_See_You packet to 192.168.0.2 w/
rcv_id 00000023
6 17:10:48.644: WCCP-PKT:D80: Received valid Here_I_Am packet from
192.168.0.2 w/rcv_id 00000022
6 17:10:48.644: WCCP-PKT:D80: Sending I_See_You packet to 192.168.0.2 w/
rcv_id 00000023
6 17:11:03.656: WCCP-PKT:D90: Received valid Here_I_Am packet from
192.168.0.2 w/rcv_id 00000023
6 17:11:03.656: WCCP-PKT:D90: Sending I_See_You packet to 192.168.0.2 w/
rcv_id 00000024
6 17:11:03.656: WCCP-PKT:D80: Received valid Here_I_Am packet from
192.168.0.2 w/rcv_id 00000023
6 17:11:03.656: WCCP-PKT:D80: Sending I_See_You packet to 192.168.0.2 w/
rcv_id 00000024
6 17:11:17.056: WCCP-PKT:D90: Received valid Here_I_Am packet from
192.168.0.2 w/rcv_id 00000024
6 17:11:17.056: WCCP-PKT:D90: Sending I_See_You packet to 192.168.0.2 w/
rcv_id 00000025
6 17:11:17.060: WCCP-PKT:D80: Received valid Here_I_Am packet from
192.168.0.2 w/rcv_id 00000024
6 17:11:17.060: WCCP-PKT:D80: Sending I_See_You packet to 192.168.0.2 w/
rcv_id 00000025
6 17:11:28.060: WCCP-PKT:D90: Received valid Here_I_Am packet from
192.168.0.2 w/rcv_id 00000025
6 17:11:28.060: WCCP-PKT:D90: Sending I_See_You packet to 192.168.0.2 w/
rcv_id 00000026
6 17:11:28.064: WCCP-PKT:D80: Received valid Here_I_Am packet from
192.168.0.2 w/rcv_id 00000025
6 17:11:28.064: WCCP-PKT:D80: Sending I_See_You packet to 192.168.0.2 w/
rcv_id 00000026
6 17:11:42.904: WCCP-PKT:D90: Received valid Here_I_Am packet from
192.168.0.2 w/rcv_id 00000026
6 17:11:42.904: WCCP-PKT:D90: Sending I_See_You packet to 192.168.0.2 w/
rcv_id 00000027
6 17:11:42.904: WCCP-PKT:D80: Received valid Here_I_Am packet from
192.168.0.2 w/rcv_id 00000026
6 17:11:42.904: WCCP-PKT:D80: Sending I_See_You packet to 192.168.0.2 w/
rcv_id 00000027
6 17:11:56.640: WCCP-PKT:D90: Received valid Here_I_Am packet from
192.168.0.2 w/rcv_id 00000027
6 17:11:56.640: WCCP-PKT:D90: Sending I_See_You packet to 192.168.0.2 w/
rcv_id 00000028
6 17:11:56.644: WCCP-PKT:D80: Received valid Here_I_Am packet from
192.168.0.2 w/rcv_id 00000027
6 17:11:56.644: WCCP-PKT:D80: Sending I_See_You packet to 192.168.0.2 w/
rcv_id 00000028
6 17:12:11.392: WCCP-PKT:D90: Received valid Here_I_Am packet from
192.168.0.2 w/rcv_id 00000028
6 17:12:11.392: WCCP-PKT:D90: Sending I_See_You packet to 192.168.0.2 w/
rcv_id 00000029
6 17:12:11.392: WCCP-PKT:D80: Received valid Here_I_Am packet from
192.168.0.2 w/rcv_id 00000028
6 17:12:11.392: WCCP-PKT:D80: Sending I_See_You packet to 192.168.0.2 w/
rcv_id 00000029
6 17:12:22.960: WCCP-PKT:D90: Received valid Here_I_Am packet from
192.168.0.2 w/rcv_id 00000029
6 17:12:22.960: WCCP-PKT:D90: Sending I_See_You packet to 192.168.0.2 w/
rcv_id 0000002A
6 17:12:22.968: WCCP-PKT:D80: Received valid Here_I_Am packet from
192.168.0.2 w/rcv_id 00000029
6 17:12:22.968: WCCP-PKT:D80: Sending I_See_You packet to 192.168.0.2 w/
rcv_id 0000002A

CME-Router#sh ip wccp
Global WCCP information:
    Router information:
        Router Identifier: 172.16.50.54
        Protocol Version: 2.0

    Service Identifier: web-cache
        Number of Service Group Clients: 0
        Number of Service Group Routers: 0
        Total Packets s/w Redirected: 0
          Process: 0
          Fast: 0
          CEF: 0
        Redirect access-list: 198
        Total Packets Denied Redirect: 0
        Total Packets Unassigned: 0
        Group access-list: -none-
        Total Messages Denied to Group: 0
        Total Authentication failures: 0
        Total Bypassed Packets Received: 0

    Service Identifier: 80
        Number of Service Group Clients: 1
        Number of Service Group Routers: 1
        Total Packets s/w Redirected: 4475
          Process: 0
          Fast: 0
          CEF: 4475
        Redirect access-list: 198
        Total Packets Denied Redirect: 0
        Total Packets Unassigned: 1853
        Group access-list: -none-
        Total Messages Denied to Group: 0
        Total Authentication failures: 0
        Total Bypassed Packets Received: 0

    Service Identifier: 90
        Number of Service Group Clients: 1
        Number of Service Group Routers: 1
        Total Packets s/w Redirected: 0
          Process: 0
          Fast: 0
          CEF: 0
        Redirect access-list: 198
        Total Packets Denied Redirect: 0
        Total Packets Unassigned: 1369
        Group access-list: -none-
        Total Messages Denied to Group: 0
        Total Authentication failures: 0
        Total Bypassed Packets Received: 0

--------------------------------------------------
From: "Ritter, Nicholas" <Nicholas.Ritter_at_americantv.com>
Sent: Tuesday, December 23, 2008 8:10 AM
To: "Roland Roland" <R_O_L_A_N_D_at_hotmail.com>
Subject: RE: [squid-users] Cisco with WCCP!! newbie here..

> Sorry for the dely in getting back to you.
>
>
> Ok....first manually check that squid is working properly. Do this by
> configuring the proxy server settings of the client browser manually to
> point to the IP of the squid server and the non-redirected port number of
> 3128 (if you are using the redirection iptables rules. This will seperate
> WCCP and iptables from squid operation. If the squid access log show
> traffic and the web browser is getting pages, switch the port number to
> port 80 on the web browser setup, this will verify iptables redirection
> functionality.
>
> If the second test fails, do a "lsmod | grep tproxy" and see if something
> like "xt_tproxy" shows up, also check the squid access log and see if it
> is the case that squid sees the client request pages, and squid is
> fetching them...it is possible that squid sees the request and is fetching
> but not getting the data back to the client.
>
> Also, check to see if the router is seeing the squid server. Do this by
> doing a "sh ip wccp" in the router and see if the client/server groups are
> greater than 0.
>
> Let me know what you see,.....we can coordinate an real-time chat sometime
> too.
>
> Nick
>
> ________________________________
>
> From: Roland Roland [mailto:R_O_L_A_N_D_at_hotmail.com]
> Sent: Sun 12/21/2008 3:13 PM
> To: Ritter, Nicholas
> Subject: Re: [squid-users] Cisco with WCCP!! newbie here..
>
>
>
> Hello :)
> I gave up!
> wccp isnt working with me...
> I've tried everything you asked me to do..
> and a few more tutorials from the net..
> NOTHING's working!!
>
> help!
>
> --------------------------------------------------
> From: "Ritter, Nicholas" <Nicholas.Ritter_at_americantv.com>
> Sent: Tuesday, December 16, 2008 11:27 PM
> To: <R_O_L_A_N_D_at_hotmail.com>
> Subject: RE: [squid-users] Cisco with WCCP!! newbie here..
>
>> Your squid.conf is missing "cache_dir" statements to tell it where to put
>> HTTP items it is caching. For squid setup you may need to review the
>> docs/wiki or use the information contained in the squid config file.
>>
>> As for the IPtables issiue, I can't help you with that without seeing the
>> error it is spitting out, and seeing the contents of
>> "/etc/sysconfig/iptables".
>>
>> Did the gre0 interface setup work?
>>
>> Nick
>>
>> ________________________________
>>
>> From: R_O_L_A_N_D_at_hotmail.com [mailto:R_O_L_A_N_D_at_hotmail.com]
>> Sent: Tue 12/16/2008 2:17 PM
>> To: Ritter, Nicholas
>> Subject: Re: [squid-users] Cisco with WCCP!! newbie here..
>>
>>
>>
>> I really cant begin to thank you for all of the help you provided so
>> far..
>> but am afraid I have to bother you one more time if possible!
>>
>> I followed your instructions one by one, but I still am facing probs.. on
>> booting I get a prob in iptables reading line1..
>> here's my squid.conf: http://pastebin.com/m401b5e09
>> and below is the debugging output:
>>
>>
>>
>> [root_at_localhost ~]# squid -NCd10
>> 2008/12/16 09:14:19| Starting Squid Cache version 2.6.STABLE6 for
>> i686-redhat-linux-gnu...
>> 2008/12/16 09:14:19| Process ID 5099
>> 2008/12/16 09:14:19| With 1024 file descriptors available
>> 2008/12/16 09:14:19| Using epoll for the IO loop
>> 2008/12/16 09:14:19| Performing DNS Tests...
>> 2008/12/16 09:14:19| Successful DNS name lookup tests...
>> 2008/12/16 09:14:19| DNS Socket created at 0.0.0.0, port 32770, FD 5
>> 2008/12/16 09:14:19| Adding nameserver 198.6.1.5 from /etc/resolv.conf
>> 2008/12/16 09:14:19| Adding nameserver 4.2.2.2 from /etc/resolv.conf
>> 2008/12/16 09:14:19| Adding domain localdomain from /etc/resolv.conf
>> 2008/12/16 09:14:19| User-Agent logging is disabled.
>> 2008/12/16 09:14:19| Referer logging is disabled.
>> 2008/12/16 09:14:19| Unlinkd pipe opened on FD 10
>> 2008/12/16 09:14:19| Swap maxSize 102400 KB, estimated 7876 objects
>> 2008/12/16 09:14:19| Target number of buckets: 393
>> 2008/12/16 09:14:19| Using 8192 Store buckets
>> 2008/12/16 09:14:19| Max Mem size: 8192 KB
>> 2008/12/16 09:14:19| Max Swap size: 102400 KB
>> 2008/12/16 09:14:19| Local cache digest enabled; rebuild/rewrite every
>> 3600/3600 sec
>> 2008/12/16 09:14:19| Rebuilding storage in /var/spool/squid (CLEAN)
>> 2008/12/16 09:14:19| Using Least Load store dir selection
>> 2008/12/16 09:14:19| Set Current Directory to /var/spool/squid
>> 2008/12/16 09:14:19| Loaded Icons.
>> 2008/12/16 09:14:19| Accepting transparently proxied HTTP connections at
>> 0.0.0.0, port 3128, FD 12.
>> 2008/12/16 09:14:19| Accepting ICP messages at 0.0.0.0, port 3130, FD 13.
>> 2008/12/16 09:14:19| WCCP Disabled.
>> 2008/12/16 09:14:19| Accepting WCCPv2 messages on port 2048, FD 14.
>> 2008/12/16 09:14:19| Initialising all WCCPv2 lists
>> 2008/12/16 09:14:19| Ready to serve requests.
>> 2008/12/16 09:14:19| Done reading /var/spool/squid swaplog (0 entries)
>> 2008/12/16 09:14:19| Finished rebuilding storage from disk.
>> 2008/12/16 09:14:19| 0 Entries scanned
>> 2008/12/16 09:14:19| 0 Invalid entries.
>> 2008/12/16 09:14:19| 0 With invalid flags.
>> 2008/12/16 09:14:19| 0 Objects loaded.
>> 2008/12/16 09:14:19| 0 Objects expired.
>> 2008/12/16 09:14:19| 0 Objects cancelled.
>> 2008/12/16 09:14:19| 0 Duplicate URLs purged.
>> 2008/12/16 09:14:19| 0 Swapfile clashes avoided.
>> 2008/12/16 09:14:19| Took 0.6 seconds ( 0.0 objects/sec).
>> 2008/12/16 09:14:19| Beginning Validation Procedure
>> 2008/12/16 09:14:19| Completed Validation Procedure
>> 2008/12/16 09:14:19| Validated 0 Entries
>> 2008/12/16 09:14:19| store_swap_size = 0k
>> 2008/12/16 09:14:20| storeLateRelease: released 0 objects
>>
>> --------------------------------------------------
>> From: "Ritter, Nicholas" <Nicholas.Ritter_at_americantv.com>
>> Sent: Tuesday, December 16, 2008 5:17 PM
>> To: "Roland Roland" <R_O_L_A_N_D_at_hotmail.com>
>> Subject: RE: [squid-users] Cisco with WCCP!! newbie here..
>>
>>> ok....given what you have presented to me below, your setup should not
>>> be
>>> working yet. It looks like there are several things that still need to
>>> be
>>> done.
>>>
>>> 1) In squid.conf add:
>>>
>>> wccp2_router 192.168.0.1
>>> wccp_version 4
>>> wccp2_rebuild_wait on
>>> wccp2_forwarding_method 1
>>> wccp2_return_method 1
>>> wccp2_assignment_method 1
>>> wccp2_service dynamic 80
>>> wccp2_service dynamic 90
>>> wccp2_service_info 80 protocol=tcp flags=src_ip_hash priority=240
>>> ports=80
>>> wccp2_service_info 90 protocol=tcp flags=dst_ip_hash,ports_source
>>> priority=240 ports=80
>>>
>>> 2) In "/etc/sysconfig/iptables" add:
>>>
>>> -A PREROUTING -i eth0 -p tcp -m tcp --dport 80 -j REDIRECT --to-ports
>>> 3128
>>> -A PREROUTING -i gre0 -p tcp -m tcp --dport 80 -j REDIRECT --to-ports
>>> 3128
>>>
>>> 3) issue command: "modprobe ip_gre"
>>> 4) issue command: "lsmod | grep gre" and make sure "ip_gre" is returned.
>>> 5) ifconfig gre0 192.168.0.7 netmask 255.255.255.0 up
>>> 6) issue command: "service iptables condrestart"
>>> 7) In your router do the following:
>>>
>>> global command: ip wccp web-cache
>>> On the interface which binds 192.168.0.1:
>>>
>>> ip wccp 80 redirect in
>>> ip wccp 90 redirect out
>>>
>>>
>>> 8) Issue (on the centos box): service squid restart
>>> 9) Wait 2 minutes, then on the router: "sh ip wccp" look for:
>>>
>>> Service Identifier: 80
>>> Number of Service Group Clients: 1
>>> Number of Service Group Routers: 1
>>>
>>> and:
>>>
>>> Service Identifier: 90
>>> Number of Service Group Clients: 1
>>> Number of Service Group Routers: 1
>>>
>>>
>>>
>>>
>>> ________________________________
>>>
>>> From: Roland Roland [mailto:R_O_L_A_N_D_at_hotmail.com]
>>> Sent: Mon 12/15/2008 5:34 PM
>>> To: Ritter, Nicholas
>>> Subject: Re: [squid-users] Cisco with WCCP!! newbie here..
>>>
>>>
>>>
>>> Hi yes I admit, ubuntu has been much easier, but nonetheless im starting
>>> to
>>> enjoy centos! has lots of command line features missing in ubuntu..
>>>
>>> anyway here's what you asked for:
>>>
>>> 1) Are you using a loopback interface in the router?
>>> No, am not.
>>>
>>> 2) What is the IP of the centos server, a client machine, and the
>>> router.
>>> Centos: 192.168.0.7
>>> Client machine: 192.168.0.2
>>> Router: 192.168.0.1
>>>
>>> 3) The output of "service iptables status"
>>>
>>>
>>> [root_at_localhost squid]# service iptables status
>>> Table: nat
>>> Chain PREROUTING (policy ACCEPT)
>>> num target prot opt source destination
>>>
>>> Chain POSTROUTING (policy ACCEPT)
>>> num target prot opt source destination
>>> 1 MASQUERADE all -- 192.168.122.0/24 0.0.0.0/0
>>>
>>> Chain OUTPUT (policy ACCEPT)
>>> num target prot opt source destination
>>>
>>> Table: filter
>>> Chain INPUT (policy ACCEPT)
>>> num target prot opt source destination
>>> 1 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp
>>> dpt:53
>>> 2 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp
>>> dpt:53
>>> 3 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp
>>> dpt:67
>>> 4 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp
>>> dpt:67
>>> 5 RH-Firewall-1-INPUT all -- 0.0.0.0/0 0.0.0.0/0
>>>
>>> Chain FORWARD (policy ACCEPT)
>>> num target prot opt source destination
>>> 1 ACCEPT all -- 0.0.0.0/0 192.168.122.0/24 state
>>> RELATED,ESTABLISHED
>>> 2 ACCEPT all -- 192.168.122.0/24 0.0.0.0/0
>>> 3 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0
>>> 4 REJECT all -- 0.0.0.0/0 0.0.0.0/0
>>> reject-with icmp-port-unreachable
>>> 5 REJECT all -- 0.0.0.0/0 0.0.0.0/0
>>> reject-with icmp-port-unreachable
>>> 6 RH-Firewall-1-INPUT all -- 0.0.0.0/0 0.0.0.0/0
>>>
>>> Chain OUTPUT (policy ACCEPT)
>>> num target prot opt source destination
>>>
>>> Chain RH-Firewall-1-INPUT (2 references)
>>> num target prot opt source destination
>>> 1 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0
>>> 2 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp
>>> type
>>> 255
>>> 3 ACCEPT esp -- 0.0.0.0/0 0.0.0.0/0
>>> 4 ACCEPT ah -- 0.0.0.0/0 0.0.0.0/0
>>> 5 ACCEPT udp -- 0.0.0.0/0 224.0.0.251 udp
>>> dpt:5353
>>> 6 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp
>>> dpt:631
>>> 7 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp
>>> dpt:631
>>> 8 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 state
>>> RELATED,ESTABLISHED
>>> 9 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state
>>> NEW
>>> tcp dpt:22
>>> 10 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state
>>> NEW
>>> tcp dpt:80
>>> 11 REJECT all -- 0.0.0.0/0 0.0.0.0/0
>>> reject-with icmp-host-prohibited
>>>
>>>
>>>
>>>
>>>
>>> 4) The output of "lsmod"
>>>
>>>
>>> Module Size Used by
>>> netloop 10945 0
>>> netbk 78145 0 [permanent]
>>> blktap 115941 2 [permanent]
>>> blkbk 22241 0 [permanent]
>>> ipt_MASQUERADE 7617 1
>>> iptable_nat 11205 1
>>> ip_nat 21101 2 ipt_MASQUERADE,iptable_nat
>>> bridge 53853 0
>>> autofs4 24389 2
>>> hidp 23105 2
>>> rfcomm 42457 0
>>> l2cap 29505 10 hidp,rfcomm
>>> bluetooth 53797 5 hidp,rfcomm,l2cap
>>> sunrpc 144893 1
>>> ip_conntrack_netbios_ns 6977 0
>>> ipt_REJECT 9537 3
>>> xt_state 6208 4
>>> ip_conntrack 53025 5
>>> ipt_MASQUERADE,iptable_nat,ip_nat,ip_conntrack_netbios_ns,xt_state
>>> nfnetlink 10713 2 ip_nat,ip_conntrack
>>> iptable_filter 7105 1
>>> ip_tables 17029 2 iptable_nat,iptable_filter
>>> ip6t_REJECT 9409 1
>>> xt_tcpudp 7105 16
>>> ip6table_filter 6849 1
>>> ip6_tables 18053 1 ip6table_filter
>>> x_tables 17349 8
>>> ipt_MASQUERADE,iptable_nat,ipt_REJECT,xt_state,ip_tables,ip6t_REJECT,xt_tcpudp,ip6_tables
>>> dm_multipath 22089 0
>>> video 21193 0
>>> sbs 18533 0
>>> backlight 10049 1 video
>>> i2c_ec 9025 1 sbs
>>> button 10705 0
>>> battery 13637 0
>>> asus_acpi 19289 0
>>> ac 9157 0
>>> ipv6 258401 15 ip6t_REJECT
>>> xfrm_nalgo 13765 1 ipv6
>>> crypto_api 11969 1 xfrm_nalgo
>>> lp 15849 0
>>> floppy 54949 0
>>> i2c_piix4 12237 0
>>> pcnet32 36805 0
>>> pcspkr 7105 0
>>> i2c_core 23745 2 i2c_ec,i2c_piix4
>>> mii 9409 1 pcnet32
>>> serio_raw 10693 0
>>> ide_cd 40033 0
>>> parport_pc 29157 1
>>> cdrom 36705 1 ide_cd
>>> serial_core 23617 0
>>> parport 37641 2 lp,parport_pc
>>> dm_snapshot 21477 0
>>> dm_zero 6209 0
>>> dm_mirror 29381 0
>>> dm_mod 61405 9
>>> dm_multipath,dm_snapshot,dm_zero,dm_mirror
>>> ata_piix 22341 0
>>> libata 144637 1 ata_piix
>>> sd_mod 24897 0
>>> scsi_mod 134861 2 libata,sd_mod
>>> ext3 123593 2
>>> jbd 56553 1 ext3
>>> uhci_hcd 25677 0
>>> ohci_hcd 23517 0
>>> ehci_hcd 33741 0
>>>
>>>
>>>
>>> 5) The output of "ifconfig"
>>>
>>> eth0 Link encap:Ethernet HWaddr 00:0C:29:C8:8E:D5
>>> inet addr:192.168.146.132 Bcast:192.168.146.255
>>> Mask:255.255.255.0
>>> inet6 addr: fe80::20c:29ff:fec8:8ed5/64 Scope:Link
>>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
>>> RX packets:1787 errors:0 dropped:0 overruns:0 frame:0
>>> TX packets:1444 errors:0 dropped:0 overruns:0 carrier:0
>>> collisions:0 txqueuelen:0
>>> RX bytes:1754176 (1.6 MiB) TX bytes:89731 (87.6 KiB)
>>>
>>> lo Link encap:Local Loopback
>>> inet addr:127.0.0.1 Mask:255.0.0.0
>>> inet6 addr: ::1/128 Scope:Host
>>> UP LOOPBACK RUNNING MTU:16436 Metric:1
>>> RX packets:2819 errors:0 dropped:0 overruns:0 frame:0
>>> TX packets:2819 errors:0 dropped:0 overruns:0 carrier:0
>>> collisions:0 txqueuelen:0
>>> RX bytes:6214808 (5.9 MiB) TX bytes:6214808 (5.9 MiB)
>>>
>>> peth0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
>>> inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link
>>> UP BROADCAST RUNNING NOARP MTU:1500 Metric:1
>>> RX packets:1790 errors:0 dropped:0 overruns:0 frame:0
>>> TX packets:1510 errors:0 dropped:0 overruns:0 carrier:0
>>> collisions:0 txqueuelen:1000
>>> RX bytes:1754743 (1.6 MiB) TX bytes:101982 (99.5 KiB)
>>> Interrupt:16 Base address:0x1080
>>>
>>> vif0.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
>>> inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link
>>> UP BROADCAST RUNNING NOARP MTU:1500 Metric:1
>>> RX packets:1444 errors:0 dropped:0 overruns:0 frame:0
>>> TX packets:1787 errors:0 dropped:0 overruns:0 carrier:0
>>> collisions:0 txqueuelen:0
>>> RX bytes:89731 (87.6 KiB) TX bytes:1754176 (1.6 MiB)
>>>
>>> virbr0 Link encap:Ethernet HWaddr 00:00:00:00:00:00
>>> inet addr:192.168.122.1 Bcast:192.168.122.255
>>> Mask:255.255.255.0
>>> inet6 addr: fe80::200:ff:fe00:0/64 Scope:Link
>>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
>>> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>>> TX packets:63 errors:0 dropped:0 overruns:0 carrier:0
>>> collisions:0 txqueuelen:0
>>> RX bytes:0 (0.0 b) TX bytes:11976 (11.6 KiB)
>>>
>>> xenbr0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
>>> UP BROADCAST RUNNING NOARP MTU:1500 Metric:1
>>> RX packets:40 errors:0 dropped:0 overruns:0 frame:0
>>> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>>> collisions:0 txqueuelen:0
>>> RX bytes:10537 (10.2 KiB) TX bytes:0 (0.0 b)
>>>
>>>
>>>
>>> 6) The output from the router of the command: "sho ip wccp"
>>>
>>>
>>> omega#sh ip wccp
>>> Global WCCP information:
>>> Router information:
>>> Router Identifier: X.X.X.X (interface facing
>>> the
>>> internet/Public ip)
>>> Protocol Version: 2.0
>>>
>>> Service Identifier: web-cache
>>> Number of Service Group Clients: 0
>>> Number of Service Group Routers: 0
>>> Total Packets s/w Redirected: 0
>>> Process: 0
>>> Fast: 0
>>> CEF: 0
>>> Redirect access-list: -none-
>>> Total Packets Denied Redirect: 0
>>> Total Packets Unassigned: 0
>>> Group access-list: -none-
>>> Total Messages Denied to Group: 0
>>> Total Authentication failures: 0
>>> Total Bypassed Packets Received: 0
>>>
>>>
>>> as for squid.conf, no I havent changed anything but these two:
>>> access list to allow my network
>>> http_access allowing that ACL.
>>>
>>>
>>> PS: I'm currently using a virtual machine, which is why you'll notice
>>> the
>>> masquarading part. it's nated to my WIFI interface.
>>> once our setup is up and running I'll move set it all up again on a
>>> server.. thought you should know :)
>>>
>>>
>>> --------------------------------------------------
>>> From: "Ritter, Nicholas" <Nicholas.Ritter_at_americantv.com>
>>> Sent: Monday, December 15, 2008 11:52 PM
>>> To: "Roland Roland" <R_O_L_A_N_D_at_hotmail.com>
>>> Subject: RE: [squid-users] Cisco with WCCP!! newbie here..
>>>
>>>> Ubuntu configures Squid more out of the box then CentOS does, which is
>>>> why
>>>> the HTTP browsing should not be working yet.
>>>>
>>>> telnet should be disabled altogether, but only in the sense of a
>>>> telnet-transport based terminal server (ie: telnetting into the centos
>>>> server to get a command shell.)
>>>>
>>>> Can you list the following:
>>>>
>>>> 1) Are you using a loopback interface in the router?
>>>> 2) What is the IP of the centos server, a client maching, and the
>>>> router.
>>>> 3) The output of "service iptables status"
>>>> 4) The output of "lsmod"
>>>> 5) The output of "ifconfig"
>>>> 6) The output from the router of the command: "sho ip wccp"
>>>>
>>>>
>>>> With the above information, I think I can straighten this out for you.
>>>> Also, did you edit the squid config file other than the "MyNet" acl and
>>>> "http_access"?
>>>>
>>>> ________________________________
>>>>
>>>> From: Roland Roland [mailto:R_O_L_A_N_D_at_hotmail.com]
>>>> Sent: Mon 12/15/2008 3:21 PM
>>>> To: Ritter, Nicholas
>>>> Subject: Re: [squid-users] Cisco with WCCP!! newbie here..
>>>>
>>>>
>>>>
>>>> ya I guess so..
>>>> but is it a firewall issue? because I could perfeclty telnet to it
>>>> doing
>>>> as
>>>> such :
>>>>
>>>> telnet 192.168.0.7 3128
>>>>
>>>> and a session opens up normaly (this is my current centos)
>>>> but I cant browse or use it as a proxy
>>>>
>>>> --------------------------------------------------
>>>> From: "Ritter, Nicholas" <nicholas.ritter_at_americantv.com>
>>>> Sent: Monday, December 15, 2008 11:18 PM
>>>> To: "Roland Roland" <R_O_L_A_N_D_at_hotmail.com>
>>>> Subject: RE: [squid-users] Cisco with WCCP!! newbie here..
>>>>
>>>>> Telnet or ssh?
>>>>>
>>>>> This is why I have issues with ubuntu. Sure things work, but often at
>>>>> the
>>>>> expense of security.
>>>>>
>>>>> Sent from my Windows Mobile® phone.
>>>>>
>>>>> -----Original Message-----
>>>>> From: Roland Roland <R_O_L_A_N_D_at_hotmail.com>
>>>>> Sent: Monday, December 15, 2008 3:02 PM
>>>>> To: Ritter, Nicholas <Nicholas.Ritter_at_americantv.com>
>>>>> Subject: Re: [squid-users] Cisco with WCCP!! newbie here..
>>>>>
>>>>> I can't believe I got back to worse than I first started!!!
>>>>>
>>>>> I can't seem to use squid now.
>>>>> I simply installed it with yum install squid on centos 5.2
>>>>>
>>>>> and added:
>>>>> acl MyNet src 192.168.0.0/24
>>>>> http_access allow MyNet
>>>>>
>>>>> that's wht I did when I frst installed it on ubuntu and it worked back
>>>>> then..!
>>>>>
>>>>> now on centos, I could telnet from outside to my box (that means it
>>>>> opened
>>>>> tht port on the firewall)
>>>>> but nothing is returned!
>>>>> heres the output of firefox when I try to open any site to test using
>>>>> my
>>>>> squid's IP/port:
>>>>>
>>>>> Connection Interrupted
>>>>> connection to the server was reset while the page was loading.
>>>>> The network link was interrupted while negotiating a connection.
>>>>> Please
>>>>> try
>>>>> again.
>>>>>
>>>>> any advice on what might be the prob ?
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>> --------------------------------------------------
>>>>> From: "Ritter, Nicholas" <Nicholas.Ritter_at_americantv.com>
>>>>> Sent: Monday, December 15, 2008 4:50 PM
>>>>> To: "Roland Roland" <R_O_L_A_N_D_at_hotmail.com>
>>>>> Subject: RE: [squid-users] Cisco with WCCP!! newbie here..
>>>>>
>>>>>> Here are some items that will need to be accomplisted:
>>>>>>
>>>>>> 1) you will need to configure iptables to redirect port 80 traffic to
>>>>>> 3128
>>>>>> 2) Setup a GRE tunnel interface between the squid box, and the
>>>>>> router.
>>>>>> 3) configure WCCP on the router
>>>>>> 4) Edit the squid.conf config file for the squid server.
>>>>>>
>>>>>>
>>>>>> With step 1, this step is largly depending on if you are ok with
>>>>>> running
>>>>>> the squid server on port 80 or not. If you choose to run the squid
>>>>>> server
>>>>>> on port 80, you still need to edit iptables rules to allow port 80
>>>>>> connections.
>>>>>>
>>>>>> Reference the following squid-cache.org wiki articles. And let me
>>>>>> know
>>>>>> where I can fill in information and specific steps to help you get up
>>>>>> and
>>>>>> running:
>>>>>>
>>>>>> http://wiki.squid-cache.org/ConfigExamples/Wccp2AndNat
>>>>>> http://wiki.squid-cache.org/ConfigExamples/SquidAndWccp2
>>>>>>
>>>>>> Create and bring up the GRE interface:
>>>>>>
>>>>>> modprobe ip_gre
>>>>>> ifconfig gre0 <address of squid server (duplicate of the eth0
>>>>>> interface
>>>>>> address)> netmask 255.255.255.0 up
>>>>>>
>>>>>> If the above commands don't give errors, you can add them to
>>>>>> "/etc/rc.d/init.d/rc.local" so that get done at each boot up.
>>>>>>
>>>>>>
>>>>>>
>>>>>> For the GRE tunnel rules for iptables, you will need something like
>>>>>> (add
>>>>>> to /etc/sysconfig/iptables, then "service iptables condrestart"):
>>>>>>
>>>>>> iptables -A INPUT -i gre0 -j ACCEPT iptables -A INPUT -i gre0 -j
>>>>>> ACCEPT
>>>>>>
>>>>>> iptables -A INPUT -p gre -j ACCEPT
>>>>>> iptables -A RH-Firewall-1-INPUT -s <address of router>/32 -p udp -m
>>>>>> udp --dport 2048 -j ACCEPT
>>>>>>
>>>>>> The first to rules allow gre protocol, and traffic onthe gre
>>>>>> interface,
>>>>>> the second rule allows WCCP control traffic.
>>>>>> ________________________________
>>>>>>
>>>>>> From: Roland Roland [mailto:R_O_L_A_N_D_at_hotmail.com]
>>>>>> Sent: Sun 12/14/2008 3:17 PM
>>>>>> To: Ritter, Nicholas
>>>>>> Subject: Re: [squid-users] Cisco with WCCP!! newbie here..
>>>>>>
>>>>>>
>>>>>>
>>>>>> Hey :)
>>>>>> I just installed centos 5.2 out of dvd with desktop-gnome.
>>>>>> and followed the instructions u've specified as well as installed
>>>>>> squid
>>>>>> using "yum install squid" and backed up squid.conf to desktop.
>>>>>> now what are the steps you want me to follow..
>>>>>>
>>>>>> thanks in advance,
>>>>>>
>>>>>> Roland
>>>>>>
>>>>>> --------------------------------------------------
>>>>>> From: "Ritter, Nicholas" <Nicholas.Ritter_at_americantv.com>
>>>>>> Sent: Friday, December 12, 2008 6:58 PM
>>>>>> To: <R_O_L_A_N_D_at_hotmail.com>
>>>>>> Subject: RE: [squid-users] Cisco with WCCP!! newbie here..
>>>>>>
>>>>>>> with the netinstall, the http url is tricky...but doable. The DVD
>>>>>>> works
>>>>>>> the best regardless. IM'ing would work better, I just don't have an
>>>>>>> IM
>>>>>>> client installed. I have an IRC client installed....or...now that I
>>>>>>> think
>>>>>>> about it...I have a gmail account....could use gmail IM...never done
>>>>>>> it
>>>>>>> though.
>>>>>>>
>>>>>>> Nick
>>>>>>>
>>>>>>>
>>>>>>> -----Original Message-----
>>>>>>> From: R_O_L_A_N_D_at_hotmail.com [mailto:R_O_L_A_N_D_at_hotmail.com]
>>>>>>> Sent: Fri 12/12/2008 9:45 AM
>>>>>>> To: Ritter, Nicholas
>>>>>>> Subject: Re: [squid-users] Cisco with WCCP!! newbie here..
>>>>>>>
>>>>>>> hey :) am downloading the DVD release just now..
>>>>>>> half way through!
>>>>>>> I got the netinstall image, burned it and gave the HTTP option a
>>>>>>> try,
>>>>>>> it
>>>>>>> gets stuck on image retrieval..
>>>>>>>
>>>>>>> I guess the DVD image would be done soon enough, I'm going to
>>>>>>> install
>>>>>>> it
>>>>>>> on
>>>>>>> a virtual machine in order to test, and if everything is setup
>>>>>>> smoothly
>>>>>>> (centos/squid) I'll proceed with the squid configuration depending
>>>>>>> on
>>>>>>> your
>>>>>>> advice..
>>>>>>>
>>>>>>> if you don't mind is there a sort of IM I could contact you on? or
>>>>>>> you
>>>>>>> prefer to keep it over here..?
>>>>>>>
>>>>>>> --------------------------------------------------
>>>>>>> From: "Ritter, Nicholas" <Nicholas.Ritter_at_americantv.com>
>>>>>>> Sent: Friday, December 12, 2008 4:51 PM
>>>>>>> To: <R_O_L_A_N_D_at_hotmail.com>
>>>>>>> Subject: RE: [squid-users] Cisco with WCCP!! newbie here..
>>>>>>>
>>>>>>>> Sure.
>>>>>>>>
>>>>>>>> I never use the live cd for installs, always other the DVD, or
>>>>>>>> netinstall
>>>>>>>> cd.
>>>>>>>>
>>>>>>>> Make sure you do a minimal install. Don't install any of the
>>>>>>>> package
>>>>>>>> groups, although it won't hurt if you do.
>>>>>>>>
>>>>>>>> If you have never installed CentOS before, let me know if you have
>>>>>>>> questions, but after the initial install and boot up, you will be
>>>>>>>> presented with a semi-graphical (ncurses) interface that has a menu
>>>>>>>> and
>>>>>>>> items on it for configuring running services, firewall, network,
>>>>>>>> etc.
>>>>>>>> You
>>>>>>>> want to make sure the box has a static IP (a private ip behind the
>>>>>>>> NAT
>>>>>>>> GW
>>>>>>>> is fine.) In the "Firewall configuration", set the "Security Level"
>>>>>>>> to
>>>>>>>> "Enabled" and "SELinux" to "Permissive". In "System Services",
>>>>>>>> disable
>>>>>>>> any
>>>>>>>> service that contains "sendmail", and/or "rpc", and/or "nfs".
>>>>>>>>
>>>>>>>> If you don't get to a menu, or want to go back to it, just type
>>>>>>>> "setup"
>>>>>>>> at
>>>>>>>> the root CLI prompt.
>>>>>>>>
>>>>>>>> Note: step 1 and 2 are separate for a reason, as it will produce
>>>>>>>> the
>>>>>>>> most
>>>>>>>> effect way of accomplishing specific goals for updating software.
>>>>>>>>
>>>>>>>> 1) run (as root): yum update yum rpm python
>>>>>>>> - this will update yum, rpm, and python
>>>>>>>> - you will be asked to confirm selections, just type: y
>>>>>>>> - you will be asked to import an GPG signing key, just type: y
>>>>>>>>
>>>>>>>> 2) run (as root): yum update
>>>>>>>> - this will update the rest of the software packages on the system
>>>>>>>> - you will be asked to confirm selections, just type: y
>>>>>>>>
>>>>>>>> 3) reboot
>>>>>>>>
>>>>>>>> -----Original Message-----
>>>>>>>> From: R_O_L_A_N_D_at_hotmail.com [mailto:R_O_L_A_N_D_at_hotmail.com]
>>>>>>>> Sent: Fri 12/12/2008 7:55 AM
>>>>>>>> To: Ritter, Nicholas
>>>>>>>> Subject: Re: [squid-users] Cisco with WCCP!! newbie here..
>>>>>>>>
>>>>>>>> Hi :)
>>>>>>>> I'm having a bit of trouble installing centos from the lvie cd..
>>>>>>>> am downloading at the moment.. centos dvd..
>>>>>>>>
>>>>>>>> in the meantime could you provide any sort of step that youd like
>>>>>>>> me
>>>>>>>> to
>>>>>>>> do..!
>>>>>>>> since im going to install squid over centos I guess your already
>>>>>>>> familiar
>>>>>>>> with all the steps?
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>> --------------------------------------------------
>>>>>>>> From: "Ritter, Nicholas" <Nicholas.Ritter_at_americantv.com>
>>>>>>>> Sent: Friday, December 12, 2008 1:54 AM
>>>>>>>> To: "RoLaNd RoLaNd" <r_o_l_a_n_d_at_hotmail.com>
>>>>>>>> Subject: RE: [squid-users] Cisco with WCCP!! newbie here..
>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>>>hey :) i cant begin to thank you for your help..
>>>>>>>>>
>>>>>>>>> No prob...I know what it is like to want to accomplish something
>>>>>>>>> and
>>>>>>>>> needing help.
>>>>>>>>>
>>>>>>>>>>>1) i dont think that would make a difference (correct me if im
>>>>>>>>>>>wrong)
>>>>>>>>>>>since the destination would only see my router's public ip!
>>>>>>>>>>>unless if theres something i'm not familiar with please do advise
>>>>>>>>>>>me
>>>>>>>>>>>whts
>>>>>>>>>>>the best course of action..
>>>>>>>>>
>>>>>>>>> If you are NATing to the Internet, than you are correct and you
>>>>>>>>> don't
>>>>>>>>> need
>>>>>>>>> client spoofing...which is good because it is easier to do.
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>>>2) Version 12.4(17b), RELEASE SOFTWARE (fc2) Cisco 2811
>>>>>>>>>>>(revision
>>>>>>>>>>>53.51
>>>>>>>>>
>>>>>>>>> Cisco IOS has been buggy at times with the WCCP feature. Make sure
>>>>>>>>> you
>>>>>>>>> are
>>>>>>>>> running something in the T release train. Do you have access to
>>>>>>>>> the
>>>>>>>>> IOS
>>>>>>>>> downloads on Cisco.com?
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>>>as for the rest, well my squid isnt active, so i dont have a
>>>>>>>>>>>problem
>>>>>>>>>>>installing CENTOS and squid again on on my box if that would help
>>>>>>>>>>>me
>>>>>>>>>>>reach >>my goal..
>>>>>>>>>>>i never used centos before! i'm only familiar with Ubuntu and
>>>>>>>>>>>fedora.
>>>>>>>>>>>but
>>>>>>>>>>>i do have one of it's images ( CentOS-5.1-i386-LiveCD )
>>>>>>>>>>>would this do?! i'll format with it and install squid on it..
>>>>>>>>>
>>>>>>>>> Get the netinstall ISO and do a minimal install and I would say
>>>>>>>>> that
>>>>>>>>> you
>>>>>>>>> could install the squid that comes with the CentOS 5.2 distro, or
>>>>>>>>> we
>>>>>>>>> can
>>>>>>>>> custom build it. After install, do a "yum update"
>>>>>>>>>
>>>>>>>>>>>do u have a specific squid version ud like to advise me with ?!
>>>>>>>>>>>or
>>>>>>>>>>>anything i should do before installign it ?
>>>>>>>>>
>>>>>>>>> The latest 2.6STABLE release is fine.
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>> Subject: RE: [squid-users] Cisco with WCCP!! newbie here..
>>>>>>>>>> Date: Thu, 11 Dec 2008 13:37:36 -0600
>>>>>>>>>> From: Nicholas.Ritter_at_americantv.com
>>>>>>>>>> To: r_o_l_a_n_d_at_hotmail.com
>>>>>>>>>>
>>>>>>>>>> Here are a few questions:
>>>>>>>>>>
>>>>>>>>>> 1) Do you want transparent redirection via WCCP with or without
>>>>>>>>>> the
>>>>>>>>>> remote website seeing the client machine IP?
>>>>>>>>>> 2) What IOS feature set and version/revision are you using on the
>>>>>>>>>> 2811
>>>>>>>>>> router? (WCCP support is buggy depending on the revision level.)
>>>>>>>>>> 3) Which version of Squid are you running?
>>>>>>>>>> 4) Which version of Linux kernel are you running?
>>>>>>>>>>
>>>>>>>>>> On you ubuntu box, run "insmod gre" then "lsmod" and see if the
>>>>>>>>>> gre
>>>>>>>>>> module loads, if you get an error, try "insmod ip_gre" instead.
>>>>>>>>>>
>>>>>>>>>> I can help you more if you are using CentOS 5.2 rather than
>>>>>>>>>> Ubuntu.
>>>>>>>>>> With
>>>>>>>>>> ubuntu, I can't give you all of the specific command lines with
>>>>>>>>>> arguments, etc.
>>>>>>>>>>
>>>>>>>>>> Nick
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>> -----Original Message-----
>>>>>>>>>> From: RoLaNd RoLaNd [mailto:r_o_l_a_n_d_at_hotmail.com]
>>>>>>>>>> Sent: Thu 12/11/2008 1:28 PM
>>>>>>>>>> To: nicholas.ritter_at_americantv.com
>>>>>>>>>> Subject: RE: [squid-users] Cisco with WCCP!! newbie here..
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>> Hi Nicholas,
>>>>>>>>>>
>>>>>>>>>> thanks for replying so soon...
>>>>>>>>>>
>>>>>>>>>> is there anything specific you'd like to know about my topology
>>>>>>>>>> in
>>>>>>>>>> order
>>>>>>>>>> for u to help out?!
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>> > Date: Thu, 11 Dec 2008 13:21:12 -0600
>>>>>>>>>> > From: Nicholas.Ritter_at_americantv.com
>>>>>>>>>> > To: r_o_l_a_n_d_at_hotmail.com; squid-users_at_squid-cache.org
>>>>>>>>>> > Subject: RE: [squid-users] Cisco with WCCP!! newbie here..
>>>>>>>>>> >
>>>>>>>>>> > I can help you out with this as needed.
>>>>>>>>>> >
>>>>>>>>>> > Nick
>>>>>>>>>> >
>>>>>>>>>> >
>>>>>>>>>> > -----Original Message-----
>>>>>>>>>> > From: RoLaNd RoLaNd [mailto:r_o_l_a_n_d_at_hotmail.com]
>>>>>>>>>> > Sent: Thu 12/11/2008 1:05 PM
>>>>>>>>>> > To: squid-users_at_squid-cache.org
>>>>>>>>>> > Subject: [squid-users] Cisco with WCCP!! newbie here..
>>>>>>>>>> >
>>>>>>>>>> >
>>>>>>>>>> > Hi All,
>>>>>>>>>> >
>>>>>>>>>> > am obviously a newbie here so am seeking an advice if i may..
>>>>>>>>>> >
>>>>>>>>>> > my current topology is as such:
>>>>>>>>>> >
>>>>>>>>>> > cisco 2811 router---Lan (contains users/squid)
>>>>>>>>>> >
>>>>>>>>>> > Squid is installed on ubuntu.
>>>>>>>>>> > and has one NIC with static ip 192.168.0.14/24
>>>>>>>>>> >
>>>>>>>>>> > i've managed to get direct proxy working with minimal
>>>>>>>>>> > settings..
>>>>>>>>>> > but am finding it hard to set it as transparent..
>>>>>>>>>> > i looked around and found at squid-cache that i could use
>>>>>>>>>> > cisco's
>>>>>>>>>> > WCCP
>>>>>>>>>> > prot=
>>>>>>>>>> > ocol...
>>>>>>>>>> > i've checked the config examples but as i'm a newbie i got a
>>>>>>>>>> > little
>>>>>>>>>> > bit
>>>>>>>>>> > los=
>>>>>>>>>> > t!!!
>>>>>>>>>> >
>>>>>>>>>> > could anyone help out?!
>>>>>>>>>> >
>>>>>>>>>> > any advice would be appreciated:)
>>>>>>>>>> >
>>>>>>>>>> > thank you in advance..
>>>>>>>>>> >
>>>>>>>>>> > Roland
>>>>>>>>>> > _________________________________________________________________
>>>>>>>>>> > Connect to the next generation of MSN Messenger
>>>>>>>>>> > http://imagine-msn.com/messenger/launch80/default.aspx?locale=en-us&source=wlmailtagline
>>>>>>>>>> >
>>>>>>>>>>
>>>>>>>>>> _________________________________________________________________
>>>>>>>>>> Explore the seven wonders of the world
>>>>>>>>>> http://search.msn.com/results.aspx?q=7+wonders+world&mkt=en-US&form=QBRE
>>>>>>>>>>
>>>>>>>>>
>>>>>>>>> _________________________________________________________________
>>>>>>>>> News, entertainment and everything you care about at Live.com. Get
>>>>>>>>> it
>>>>>>>>> now!
>>>>>>>>> http://www.live.com/getstarted.aspx
>>>>>>>>>
>>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>
>>>>>
>>>>
>>>>
>>>>
>>>>
>>>
>>>
>>
>>
>>
>>
>
>
>
>
Received on Fri Jan 16 2009 - 16:24:09 MST